Adept Python User Manual Page 129
- Page / 170
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
PDU3 Specifications
Adept Python Modules User’s Guide, Rev. E 129
8.9 PDU3 Specifications
Table 8-2. PDU3 Specifications
Input Power Requirements
Universal power input voltage 200-240 VAC (180-264 VAC max),
single phase
Power input frequency 50-60 Hz (47 - 63 Hz max)
Power input current 8 Amps
Power Input connector (mating) IEC 320 C13
Power Installation Category II Overvoltage
Amplifier DC Output
Output Voltage 24 VDC ±10%
Output Current 3 Amps maximum
a
a
Note: maximum combined amplifier DC output current and Aux/IO Blox output
current may not exceed 4 amps.
Hold up time 20 ms
AUX DC Output
Output Voltage 24 VDC +10% -15%
Output Current 3 Amps maximum
a
Hold up time 20 ms
Switched AC Output Section
Maximum Continuous Output Current 6 Amps
Output Voltage equal to input
Power Output Connector (mating) IEC 320 C14
Environmental
Ambient temperature 5° C to 40° C (41 to 104° F)
Humidity 5 to 90%, noncondensing
Pollution degree 2 (per IEC 1131-2/EN 61131-2)
Chassis protection class, unmounted IP-20 (NEMA Type 1)
Weight 2.2 kg
- Adept Python 1
- Table of Contents 5
- List of Figures 11
- Introduction 1 15
- L18 Module with 16
- MotionBlox-10 Amp 16
- L12 Module with 16
- Product Description 17
- Special and Custom Orders 18
- Adept SmartController CX 18
- 1.4 How Can I Get Help? 21
- 1.5 Related Manuals 22
- Safety 2 23
- 2.3 Risk Assessment 25
- Avoidance 26
- Maximum Thrust 27
- Safety Barriers 28
- 2.5 Equipment Modifications 30
- 2.6 Transport 31
- 2.8 Sound Emissions 32
- 2.9 Thermal Hazard 32
- 2.10 Working Areas 32
- Python Linear Module 37
- Descriptions 3 37
- L-Series Module Types 38
- Payloads and Moments 38
- Stroke Length 41
- Accuracy 41
- Acceleration 43
- Resolution and Repeatability 43
- 143.50 mm 45
- 168.50 mm 45
- 295.50 mm 46
- Motor Mount Configuration 47
- Linear Module Options 49
- Harness Exit Configurations 50
- Module Preparation (Assembly) 51
- L18 030 S10 B0 M10 0 P0 0 0 52
- L18 030 S10 B0 53
- M10 0 P0 0 0 54
- L08 010 S10 B0 57
- LG6 020 P0 0 0 59
- Python Theta Module 61
- Description 4 61
- Gear Ratio 63
- Interface 63
- ± 360° RANGE OF MOTION 64
- (CONTINUOUS TURN AVAILABLE) 64
- LT1 G30 B0 64
- Module System Descriptions 5 67
- 10 S 1 0 0 0 69
- A0 A0 A0 A0 X00 0 70
- S 2 0 0 0 72
- Single-Axis Configurations 73
- Z-Axis motion 74
- Single-Axis Theta Modules 75
- 5.4 System Orientation 86
- Single-Axis Orientations 87
- Typical Two-Axis Orientations 87
- Module 1, Flipped 89
- Module 2, Rolled 89
- (Amp 2 facing Amp 1) 89
- 5.5 Mounting Options 90
- Mounting Feet Drawings 91
- Toe Clamp Drawings 92
- All dimensions 93
- CABLE 4 KIT - No cable 97
- CABLE 1 KIT - No cable 97
- 5.7 Gantry Mounting Kits 98
- GANTRY MOUNTING 99
- Dimension determined 100
- Y module 100
- LG6 Gantry Support Module 100
- 5.8 IO Blox 103
- IO BLOX OPTIONS 104
- CABLING/PLUMBING 107
- Module Installation 6 109
- Mounting Plate 110
- General Installation Notes 110
- Cleanroom System Installation 115
- Space Around the Chassis 117
- 7.2 System Cable Diagram 118
- 7.3 Installing the PDU3 119
- Power Distribution Unit 8 121
- 8.2 Installing the PDU3 122
- 200–240V~ 123
- 380–415V~ 123
- 8.5 PDU3 Fuses 125
- 8.6 PDU3 Mounting Brackets 126
- 8.7 PDU3 Dimensions 127
- Note: All dimensions 128
- 8.9 PDU3 Specifications 129
- XDCS Connector 131
- XSLV1/2 Connector 131
- Adept MB-10 Amps 9 133
- 9.2 MB-10 Operation 134
- Indicator LED 135
- Brake Release Button 135
- MB-10 Connectors 135
- IO Blox Connector 136
- 9.3 MB-10 Firmware 137
- 9.4 MB-10 Specifications 138
- Motor Connector 139
- Encoder Connector 139
- System Operation 10 143
- Power Checks 144
- Cable Installation Checks 144
- 10.3 Turning On Power 145
- 10.4 Software Configuration 145
- Load and Run DC_SETUP.V2 146
- 10.5 Enable High Power 150
- 10.6 Run-Time Calibration 151
- 10.7 Turning Off Power 151
- Maintenance 11 153
- 11.2 Checking Safety Systems 154
- Battery Replacement Procedure 155
- Retaining clip 156
- Replacement 158
- 11.6 Additional Maintenance 159
- 11.7 MB-10 Decommissioning 159
- Advanced System 161
- Configurations 12 161
- Robot #1 Robot #2 162
- User-Supplied 163
- 24VDC Power 163
- Terminator 164
- Installed 164
- 5960 Inglewood Drive 170
- Pleasanton, CA 94588 170
- 925·245·3400 170
Related products and manuals for Equipment Adept Python
Equipment Adept AnyFeeder User Manual
(68 pages)
(68 pages)
© 2020, manymanuals.com. All rights reserved. | 1.514 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals